surface piercing propeller surface propeller surface propulsion system

arneson surface driver,surface technology system,surface propulsion system,surface propeller,surface piercing propeller,marine propulsion,marine transmission,production propulsion system,waterjet drives,waterjet propulsion,boat propulsion,pulse drive,underwater propeller,surface drive,eco drive.
arneson surface driver,surface technology system,surface propulsion system,surface propeller,surface piercing propeller,marine propulsion,marine transmission,production propulsion system,waterjet drives,waterjet propulsion,boat propulsion,pulse drive,underwater propeller,surface drive,eco drive.

A separate connector is provided for each of the three surface piercing propeller station control head cables, the optional speed sensor cables, a communication cable, and one multi-purpose cable for power, troll, and options. The stainless steel control housing includes isolated mounting feet, a topside access panel for setup, and cable clamp brackets for mounting mechanical push-pull cables surface piercing propellerto interface to throttle governors and transmission selector levers.Throttle surface piercing propellerlever and transmission direction selections are combined into the lever motion. A multi-function rotary selector provides for idle lever selection, and activation of troll or synchronization options surface piercing propellerwhen available in the system. A guarded station select push-button and individual surface piercing propellerstation selected indicators are provided for command and identification of station in control. The station select push-button is also used to enter the direction override by holding down while leaving neutral. Neutral surface piercing propellerindicators are also provided and are controlled by circuitry which monitors the gear command and the output of the control. Neutral surface piercing propellerindicators will blink when in neutral gear condition is a result of a direction override.Trolling valves surface piercing propellercan be controlled surface piercing propellermechanically or electronically. In systems that have mechanically positioned governors and transmission selectors, it may be necessary to use a separate external troll actuator. In systems with electronic surface piercing propellerengines or solenoid shift options, surface piercing propellera troll actuator may be included in the main control enclosure and eliminate the need for additional wiring and mounting.Operation surface piercing propellerof systems with three to five engines can be simplified by the use of Phantom Controls to duplicate gear and throttle commands to inward surface piercing propellerand center propulsion units. Single, dual, and triple Phantoms allow full operation of the boat's propulsion surface piercing propellerfrom one dual lever control head when surface piercing propellerPhantoms are enabled, and separate levers or combinations when Phantoms are disabled.The EC200 control system is surface piercing propellerdesigned to meet or exceed the following specifications. These specifications are selected to satisfy US, Australian, and European regulatory agency requirements and recommendations.Operating: 0 to 70 degrees Celsius ambient Storage: surface piercing propellerCelsius ambient Relative humidity from 0 to 100% Splash and spray up to 15 PSI on all normally exposed s and 5 PSI on all s which are normally inside or protected from piercing propellerweather and waves 8 g's, 3 planes, 0.15 displacement, piercing propeller., 1 million cycles The bonding circuitry piercing propellerdesign of the EC200 control system allows it to work in either piercing propellerbattery negative to control enclosure wiring, or European/Australian totally isolated battery negative wiring, with control enclosure tied to hull plate or not piercing propellerconnected at all. 150 volts per meter for control head and associated cable 100 volts per meter for entire system, piercing propellerfrom 10 kilohertz to 10 gigahertz 12 volt system - ("A" suffix) 10 volts to 16 volts operation, 9 volts cranking 24 volt system - ("B" suffix) 20 volts to 32 piercing propellervolts operation, 18 volts cranking CURRENT REQUIREMENTS12 volt system - 15 amps peak (2 seconds per command change), 1 amp nominal 24 volt system - 8 amps peak (2 seconds per command change), 0.8 amps nominal Note: The above current requirements are based on control systems that have actuators for both throttle and gear.

 

arneson surface driver, surface technology system, surface propulsion system ,
surface propeller,surface piercing propeller,marine propulsion,marine transmission,production propulsion system,waterjet drives,boat propulsion,pulse drive,underwater propeller,surface drive,eco drive,waterjet propulsion.